Configure remove-private-as on BGP Peer

To enable external connectivity, configure remove-private-as attribute when you create or update BGP peer.

By default, remove-private-as is disabled.

About this task

Follow this procedure to configure a remove private as.

Procedure

  1. Run the following command to create remove private as when you create a BGP Peer on a tenant VRF: 
    efa tenant service bgp peer create --name <bgp-peer-name> --tenant <tenant-name> 
     --ipv4-uc-nbr <device-ip,vrf-name:neighbor-ip,remote-asn> 
     --ipv4-uc-nbr-bfd <switch-ip,vrf-name:ipv4-neighbor,bfd-enable(t/f),bfd-interval,bfd-rx,bfdmult> 
     --ipv4-uc-nbr-remove-private-as <device-ip,vrf-name:neighbor-ip,true|false>
  2. Run the following command to create remove private as when you update a BGP Peer on a tenant VRF: 
    efa tenant service bgp peer update --name <bgp-peer-name> --tenant <tenant-name>
 
     --operation peer-add
     --ipv4-uc-nbr 10.20.246.25,v1:10.20.30.50,50000 
     --ipv4-uc-nbr-bfd 10.20.246.25,v1:10.20.30.50,true 
     --ipv4-uc-nbr-remove-private-as 10.20.246.25,v1:10.20.30.50,true 
     --ipv4-uc-nbr 10.20.246.26,v1:10.20.30.50,50000 
     --ipv4-uc-nbr-bfd 10.20.246.26,v1:10.20.30.50,true 
     --ipv4-uc-nbr-remove-private-as 10.20.246.26,v1:10.20.30.50,false
    Example:
    efa tenant service bgp peer create --name ten1bgppeer1 --tenant tenant11 
	--ipv4-uc-nbr 10.20.246.25,v1:10.20.30.40,50000 
	--ipv4-uc-nbr-bfd 10.20.246.25,v1:10.20.30.40,true 
	--ipv4-uc-nbr-remove-private-as 10.20.246.25,v1:10.20.30.40,true 
	--ipv4-uc-nbr 10.20.246.26,v1:10.20.30.40,50000 
	--ipv4-uc-nbr-bfd 10.20.246.26,v1:10.20.30.40,true 
	--ipv4-uc-nbr-remove-private-as 10.20.246.26,v1:10.20.30.40,true



    10.20.246.25
ORCA_01# show running-config router bgp
address-family ipv4 unicast vrf v1
  redistribute connected
  neighbor 10.20.30.40 remote-as 50000
  neighbor 10.20.30.40 remove-private-as
  neighbor 10.20.30.40 bfd
  neighbor 10.40.40.253 remote-as 4200000000
  neighbor 10.40.40.253 next-hop-self
  maximum-paths 8
 !
    		 
    10.20.246.26 
ORCA_02# show running-config router bgp
address-family ipv4 unicast vrf v1
  redistribute connected
  neighbor 10.20.30.40 remote-as 50000
  neighbor 10.20.30.40 remove-private-as
  neighbor 10.20.30.40 bfd
  neighbor 10.40.40.252 remote-as 4200000000
  neighbor 10.40.40.252 next-hop-self
  maximum-paths 8
 !
    		 
    efa tenant service bgp peer show --detail

    Name        : ten1bgppeer1
Tenant      : tenant11
State       : bgp-peer-created
Description : 

Static Peer
-----------
Device IP             : 10.20.246.25
VRF                   : v1
AFI                   : ipv4
SAFI                  : unicast
Remote IP             : 10.20.30.40
Remote ASN            : 50000
Next Hop Self         : false
Update Source IP      : 
BFD Enabled           : true
BFD Interval          : 0
BFD Rx                : 0
BFD Multiplier        : 0
MD5 Password          : 
Remove Private AS     : true
Default Originate     : false
Default Originate Route Map : 
Prefix List In        : 
Prefix List Out       : 
Route Map In          : 
Route Map Out         : 
Dev State             : provisioned
App State             : cfg-in-sync

    Device IP             : 10.20.246.25
VRF                   : v1
AFI                   : ipv4
SAFI                  : unicast
Remote IP             : 10.20.30.50
Remote ASN            : 50000
Next Hop Self         : false
Update Source IP      : 
BFD Enabled           : true
BFD Interval          : 0
BFD Rx                : 0
BFD Multiplier        : 0
MD5 Password          : 
Remove Private AS     : true
Default Originate     : false
Default Originate Route Map : 
Prefix List In        : 
Prefix List Out       : 
Route Map In          : 
Route Map Out         : 
Dev State             : provisioned
App State             : cfg-in-sync

Device IP             : 10.20.246.26
VRF                   : v1
AFI                   : ipv4
SAFI                  : unicast
Remote IP             : 10.20.30.50
Remote ASN            : 50000
Next Hop Self         : false
Update Source IP      : 
BFD Enabled           : true
BFD Interval                : 0
BFD Rx                      : 0

    BFD Multiplier        : 0
MD5 Password          : 
Remove Private AS     : false
Default Originate     : false
Default Originate Route Map : 
Prefix List In        : 
Prefix List Out       : 
Route Map In          : 
Route Map Out         : 
Dev State             : provisioned
App State             : cfg-in-sync

Device IP             : 10.20.246.26
VRF                   : v1
AFI                   : ipv4
SAFI                  : unicast
Remote IP             : 10.20.30.40
Remote ASN            : 50000
Next Hop Self         : false
Update Source IP      : 
BFD Enabled           : true
BFD Interval          : 0
BFD Rx                : 0
BFD Multiplier        : 0
MD5 Password          : 
Remove Private AS     : true
Default Originate     : false
Default Originate Route Map : 
Prefix List In        : 
Prefix List Out       : 
Route Map In          : 
Route Map Out         : 
Dev State             : provisioned
App State             : cfg-in-sync
  3. Verify the switch configuration on the SLX device. 
    Rack1-Device1# show running-config router bgp
router bgp
 local-as 4200000000
 capability as4-enable
 fast-external-fallover
 neighbor 10.20.20.4 remote-as 4200000000
 neighbor 10.20.20.4 next-hop-self
 address-family ipv4 unicast
  network 172.31.254.46/32
  network 172.31.254.123/32
  maximum-paths 8
  graceful-restart
 !
 address-family ipv4 unicast vrf ten1vrf1
  redistribute connected
  neighbor 10.20.30.40 remote-as 50000
  neighbor 10.20.30.40 remove-private-as
  neighbor 10.20.30.40 bfd
  neighbor 10.20.30.50 remote-as 50000
  neighbor 10.20.30.50 remove-private-as
  neighbor 10.20.30.50 bfd
  maximum-paths 8
 !
 address-family ipv6 unicast
 !
 address-family ipv6 unicast vrf ten1vrf1
  redistribute connected
  maximum-paths 8
 !
 address-family l2vpn evpn
  graceful-restart
 !
!
    		 
    Rack1-Device2# show running-config router bgp
router bgp
 local-as 4200000000
 capability as4-enable
 fast-external-fallover
 neighbor 10.20.20.5 remote-as 4200000000
 neighbor 10.20.20.5 next-hop-self
 address-family ipv4 unicast
  network 172.31.254.46/32
  network 172.31.254.176/32
  maximum-paths 8
  graceful-restart
 !
 address-family ipv4 unicast vrf ten1vrf1
  redistribute connected
  neighbor 10.20.30.40 remote-as 50000
  neighbor 10.20.30.40 remove-private-as
  neighbor 10.20.30.40 bfd
  neighbor 10.20.30.50 remote-as 50000
  neighbor 10.20.30.50 remove-private-as
  neighbor 10.20.30.50 bfd
  maximum-paths 8
 !
 address-family ipv6 unicast
 !
 address-family ipv6 unicast vrf ten1vrf1
  redistribute connected
  maximum-paths 8
 !
 address-family l2vpn evpn
  graceful-restart
 !
!
    Note

    Note

    For information about commands and supported parameters to configure remove-private-as attribute, see ExtremeCloud Orchestrator Command Reference, 3.6.0 .
9038968-00 Rev AB